![]() Then after that, any time that both speaker and that device have Bluetooth turned on, and they’re near to each other, pairing would automatically take place once more. Another way to fix the sound issues with your Sony TV is to reset the. Thus, to restore this auto syncing, you manually pair the X11 with a device. Sony Bravia Tv Sound Not WorkingMake sure you are connected to the TV via HDMI. So you may now sell or gift the unit, or pair it again with your favorite Bluetooth devices.Īfter a hard reset, the speaker no longer automatically connects with any previously paired Bluetooth device. Done with How to Hard Reset the Sony X11 Bluetooth Speaker ! This is a signal for you to look for this speaker on a nearby BT device, and pair to it if you so desire. The Status lamp blinks white rapidly to tell you this. To run the factory reset, press the Home button on your remote and choose Settings, followed by Storage and Reset. Note that after a hard reset, this speaker comes up in pairing mode. Next, power on the X11 once more, as described in step 1 above. Check that your Sony X11 Speaker Did Indeed Hard Reset You may release the buttons when the Statuslamp goes out. Note that on this speaker, there is no power-down sound. Then the speaker powers OFF, and the status lamp goes dark, as shown next. The X11 then enters the hard reset process after a short pause. The -Power-, -Volume DOWN-, and -Volume UP- buttons. All three of them we find on the top of the speaker, near the front edge, as called out in the next picture. Press and Hold the Volume DOWN, Volume UP, and Power Buttons at the Same Timeįind these buttons as shown next. Audio output Adjust for headphones and audio system. If this does not do it, Sony TV Not Finding Channels) which should blank all the. Reset Return all sound settings to factory default settings. If you are not, try a reset, change the volume and source input. For details, refer to Performing acoustic auto calibration. No sound or only a very low-level sound of the device connected to the speaker system is heard. The TV sound from this speaker system lags behind the image. The sound is interrupted while watching a TV program or content on a Blu-ray Disc, etc. ![]() ![]() Acoustic auto calibration Adjust audio output based on your watching environment. The sound is output from both the speaker system and TV. ![]() But whether it pairs or not, this reset routine works the same way, as follows. TV position Output sound from the TV speakers according to the position of the TV. The speaker makes a ding-dong beep sound when it powers up, whether it connects to a nearby device or not. This light we find on the bottom edge of the front of the unit. Then, the status light comes on, as shown next. The Sony X11 -Power- button.įind the Power button, as shown in the last picture above. Find the Powerbutton as shown in the next picture. Press and release the Powerbutton for a half-second or so. How to Hard Reset the Sony X11 Speaker 1. Also, you would best reset your speaker to get it ready for sale or re-gifting, or to stop it from pairing with devices you no longer wish it to connect with. We might want to clear these to prevent this speaker from pairing to any nearby Bluetooth devices. Plus, doing this erases any earlier paired Bluetooth devices from memory. Hard resetting restores the X11 to factory default state. Manuals are posted on your model support page.Show you how to Hard reset your Sony X11 personal cube speaker to its default settings. For instructions about performing a Factory Reset, consult the instruction manual of the TV for model-specific information. NOTE: Performing a Factory Reset may also help resolve the issue. If the volume cannot be adjusted using the volume buttons on the remote control or television, then perform a power reset on the TV.If the volume can be adjusted using the volume buttons on the TV, but not the remote control, then reset the remote control to factory specifications.Attempt to adjust the volume using the remote control supplied with the TV.Attempt to adjust the volume using the volume control buttons on the front of the TV.If this is the case, use the audio receiver remote control to adjust the volume through the audio system. IMPORTANT: If the Audio Out option of the television is set to Fixed, the TV speakers are turned off and the volume output of the TV is fixed. Depending on your model, you can either: Press and hold the POWER button until the TV shuts down and restarts or Press and hold the POWER button until a menu appears, and select Restart Option 2: Force Restart the TV in the TV settings. Follow the steps below to troubleshoot if the TV volume cannot be adjusted. Option 1: Force Restart the TV with the remote control Power button.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |